|
UGU: Unix Guru Universe - Xenix FAQ
- Home : Unix Flavors
: Xenix
Xenix FAQ
XENIX Patches
Newsgroups: comp.unix.xenix.sco,news.answers
From: chip@unicom.com (Chip Rosenthal)
Subject: Welcome to comp.unix.xenix.sco [monthly FAQ posting]
Followup-To: comp.unix.xenix.sco
Summary: answers to frequently asked questions
Approved: news-answers-request@MIT.Edu
Archive-name: sco-xenix
News-answers-archive-name: sco/xenix
Posting-frequency: monthly
Version: $Id: sco-xenix,v 1.64 1996/07/21 01:20:54 chip Exp $
------------------------------
Subject: ***** Introduction
Welcome to comp.unix.xenix.sco. This newsgroup is about the Xenix
operating system from the Santa Cruz Operation (SCO). If you have an
SCO Xenix question, then you've come to the right place.
This is NOT the newsgroup for SCO Unix questions. If you want to talk
about other SCO operating systems, please show some courtesy and use
one of the comp.unix.sco.* groups. This also is NOT the right place
for questions about Xenix implementations from other vendors. Use
comp.unix.xenix.misc.
Certain questions are asked frequently on the net. Frequently asked
questions (FAQs) get old and boring after a while. We can stamp out
FAQs in your lifetime! Please review this message before posting your
question to comp.unix.xenix.sco.
If you haven't already done so, please read the periodic postings in
news.announce.newusers entitled "A Primer on How to Work With the Usenet
Community", "Answers to Frequently Asked Questions about Usenet" and
"Hints on writing style for Usenet". You should also review the
comp.unix.questions FAQ postings. These answer general questions,
such as `How do I delete a file with funny characters in the name?'
and `How can I change my shell prompt?' C programmers should check
out the FAQ in comp.lang.c.
Whenever we talk about Xenix here, we really mean SCO Xenix System V.
Our comments often won't apply to the other kinds of Xenix. Also, be
particularly careful if you use Xenix/286. It's been ages since we've
used it and some of our suggestions might not apply.
This message is maintained and posted monthly by Chip Rosenthal. Your
corrections, additions, and comments are encouraged. Please mail them
to chip@chinacat.unicom.com. These questions and answers were written
by Chip Rosenthal, Jeff Liebermann, Ronald Florence, Chip Salzenberg,
Ronald Khoo, Vic Michael, and Stephen Bleazard. Helpful contributions
and comments have been provided by Andrew Phillips, Peter Funk, Paul
Warren, Lawrence Kirby, Kai Ruottu, Ray Malitzke, Chet Creider, Greg
Lehey, Marc Brumlik, Monty Solomon, and Bela Lubkin.
Please examine the date near the top of this message. This message
is updated from time to time, and older versions might be obsolete.
The most up-to-date version of these guidelines are available on
the World-Wide Web as . For
the web-impaired, try anonymous FTP to "ftp.unicom.com:/pub/FAQ/sco-xenix".
If all else fails, try the standard FAQ archive on rtfm.mit.edu.
------------------------------
Subject: ***** Table of Contents
===> Product Questions:
QA1. What is the difference between Unix and Xenix?
QA2. What is the minimum system required to run Xenix?
QA3. Should I buy Unix or Xenix?
QA4. What are the current Xenix versions?
QA5. Where can I get Xenix fixes?
QA6. I'm using an older Xenix/386 version. What fixes do I need?
QA7. Does SCO have a BBS?
===> General Xenix Questions:
QB1. Can't boot. My system used to work.
QB2. Configure(ADM) fails when I modify my system name.
QB3. The system is crashing with `parity error' panics.
QB4. Login fails without prompting for password.
QB5. Can I use `gcc' instead of buying the SCO Development System?
QB6. Program `foobar' dumps core with a stack overflow. [Xenix 286]
QB7. Spell cannot initialize hash table.
QB8. Will my laser printer work with the Text Processing Package?
QB9. Where is crypt?
QB10. How can email handle `internet' addresses or use a `smart host'?
QB11. Where can I find freely available software for Xenix?
QB12. Why don't my arrow keys work in `vi'?
QB13. Why does `cron' die periodically?
===> Disk and Filesystem Questions:
QC1. Can I use a disk bigger than 1024 cylinders?
QC2. Why won't Xenix recognize my SCSI disk?
QC3. Where is the `/u' filesystem I created?
QC4. `WARNING!! - mounting: as ' message when booting.
QC5. `POSSIBLE FILE SIZE ERROR' when running `fsck'.
QC6. Is disk fragmentation curable?
QC7. Can I put a CD-ROM drive on my Xenix system?
===> Communications Questions:
QD1. How do I add more than 2 COM ports?
QD2. How do I set a 19,200 baud rate?
QD3. How can I have more mscreen(C) sessions?
QD4. Upgraded to 2.3.4 and flow control broke with mscreen(C).
QD5. Terminals act funny, modems drop characters, help!!
QD6. Does Xenix support 16550A UARTs?
QD7. How do I increase the number of `clists'?
QD8. How do I change the 16550A trigger level?
QD9. How do I adjust the `ttyhog' value?
QD10. BSD based uucp can't connect to my machine.
QD11. uucp truncates my system name to seven characters!
QD12. What is the uucp `windows' patch?
QD13. uucp gives `alarm' messages, eventually dies.
===> Display and Graphics Questions:
QE1. How come Xenix won't recognize my VGA display?
QE2. How can I do a printscreen under Xenix?
QE3. How can I blank the console display when it is idle?
QE4. How can I do graphics under Xenix? What programs are available?
QE5. CGI graphics mangles grey scale on a mono VGA.
QE6. CGI graphics fail on a LaserJet in landscape mode.
===> Networking Questions:
QF1. What do I need to run TCP/IP?
QF2. What do I need to run NFS?
QF3. How can I run uucp over TCP/IP?
QF4. What does "NOTICE: tcp sum: src C06C6901, sum 0000B004" mean?
===> Xenix and MS-DOS Interoperability Questions:
QX1. Can Xenix share a hard disk with MS-DOS?
QX2. Can Xenix access MS-DOS disks?
QX3. Can Xenix execute MS-DOS programs?
QX4. Can MS-DOS execute Xenix programs?
===> The (in)Famous Xenix Cheat-Sheet:
QZ1. What the $%*&! is happening?
------------------------------
Subject: ***** SECTION A - Product Questions
QA1. What is the difference between Unix and Xenix?
Xenix is Unix -- or at least one flavor of it. In the late 70's,
Microsoft licensed the Unix sources from AT&T and ported them to
a number of platforms. In those days, AT&T would license the Unix
software but not the Unix name, thus each company had to invent
their own name. Microsoft picked Xenix. Microsoft did not sell
Xenix to end users. Instead, they licensed the software to OEMs
(Intel, Tandy, Altos, SCO, etc.) who provided a finished end-user
package. Microsoft no longer supports Xenix, and in fact never
even offered a 286 or 386 version.
Several Unix implementations for the PC architecture have been
tried with varying levels of success. SCO Xenix for the PC/XT
was one. Nearly all of the PC/XT implementations were clunkers,
because the machine lacked the hardware necessary for robust Unix
operations. The PC/AT offered hardware memory protection, and
SCO Xenix/286 took advantage of it. SCO Xenix/386 added demand
paged virtual memory. These added features made multiuser PCs
viable, and SCO Xenix popular.
SCO Xenix starts with a Unix System III base, throws in several
Berkeley enhancements, and adds features to obtain conformance to
the System V Interface Definition (SVID). Today, the bulk of the
code is from System V. Xenix/386 even has capabilities to execute
Unix programs. It differs, however, in many of the SVID `optional'
areas people tend to expect of a full System V. SCO Xenix lacks
a real `inittab', for example. You need to go to a real System V,
such as SCO Unix, for all these features.
QA2. What is the minimum system required to run Xenix?
You can build a minimal, single-user Xenix system with an 80386SX
computer, 2MB to 4MB RAM, and 40MB hard disk. A pretty spiffy
system, suitible for development, would be an 80386DX computer
with 4MB RAM and 80MB hard disk. Additional resources (more speed,
more RAM, more disk) will be required to support additional users,
large applications, networking, or X windows. Xenix/286 will run
on a PC/AT, but you will quickly become frustrated with its
limitations, especially if you are a programmer.
QA3. Should I buy Unix or Xenix?
If you are happy running Xenix now, don't rush to throw it away.
Xenix will be around for some time. If, however, you are new to
multi-user computing, you should consider Unix System V Release
3.2 or Release 4.X.
There are a number of reasons why Xenix is slowly fading. It is
a mature product. There will be few future enhancements. Fewer
and fewer vendors are supporting it. Nearly every program written
for Xenix will run under Unix too. Unix offers a lot more goodies
and better performance than Xenix.
One advantage to Xenix is that it requires less memory and disk
space. At today's hardware prices that usually isn't a big deal.
There are certain applications, however, where this is attractive.
Although Unix has a lot more to offer, a number of Xenix enthusiasts
wouldn't switch if you gave them a free copy of Unix. They would
gladly forego the new features to avoid the bloat of System V.
QA4. What are the current Xenix versions?
Package Version `perms' file
---------------------- -------------- ---------------------------
Xenix Runtime System 2.3.4 inst, dsmd, tpmd, rts, ext
Xenix Runtime (286) 2.3.2 inst, dsmd, tpmd, rts, ext
Development System(386) 2.3.1 soft
Development System(286) 2.2.1 soft
CGI 1.1.0 cgi
Text Processing 2.3.0 text
Manual Pages 2.3.0 man
VP/ix 1.2.0 vpix
TCP/IP Runtime 1.2.0 tcprt
TCP/IP Development 1.0.1 tcpdev
Streams Runtime 1.0.0 streamsrt
Streams Toolkit 1.0.0 streamstk
Int'l Supplement(386) 2.1.0 sup.os
Int'l Supplement(286) 2.0.0 sup.os
The perms column lists files found in the /etc/perms directory.
The `#rel=' line in these files will tell you what version you
have.
QA5. Where can I get Xenix fixes?
SCO provides Support Level Supplements (SLS) at no charge. There
are several places that make them available through anonymous uucp
and anonymous ftp.
Internet users may retrieve SLSs by anonymous ftp from `ftp.sco.com'
(see /SLS/info) and `ftp.uu.net' (see /vendor/sco/SLS/info).
SLSs may be downloaded with anonymous uucp from SCO's `sosco'
machine. To retrieve a shopping list of available SLSs, add one
of the following to your `/usr/lib/uucp/Systems' file:
# Telebit (PEP) modem
sosco Any ACU 19200 14084291786u gin:-BREAK-gin:-BREAK-gin: uusls
# Hayes V-Series modem
sosco Any ACU 19200 14084274470 gin:-BREAK-gin:-BREAK-gin: uusls
# 1200 or 2400 bps modem
sosco Any ACU 300-2400 14084253502 gin:-BREAK-gin:-BREAK-gin: uusls
European folks might prefer to use `scolon' instead. From within
the UK, try:
scolon Any ACU 300-19200 0923210911u \
gin:-BREAK-gin:-BREAK-gin: uusls word: bbsuucp
Outside the UK, replace the leading zero with the country code.
A 9600bps Trailblazer answers this line. Delete the `u' at the
end of the phone number if you aren't using a Telebit modem.
Files are as on `sosco' but tend to be a week or so behind. Also,
replace `sosco' with `scolon' `sosffm' in the examples below.
In Germany, you can use:
sosffm Any ACU 300-9600 069-50910736 \
"" \r ogin:-BREAK-ogin: uusls sword: bbsuucp
This modem supports V.32 transfers, but not PEP. We've been told
this system is often behind the other sites.
[LATE BREAKING NEWS: We've been told that "sosffm" has moved.
If anybody knows where it went, please let the FAQ editor
know. Thanks. -ed]
Add to your `/usr/lib/uucp/Permissions' file:
# REQUEST files only - i.e. cannot send to sosco.
# rmail required to get bounced mail and error messages.
MACHINE=sosco SENDFILES=yes REQUEST=no COMMANDS=rmail:uucp \
WRITE=/usr/spool/uucppublic:/tmp
To retrieve an SLS listing to your machine as /tmp/info:
uucp sosco\!/usr/spool/uucppublic/SLS/info /tmp/info
This file also provides directions on retrieving, unarchiving,
and uncompressing the SLSs. There is also a `descriptions' file
with additional details on the available SLSs.
SLSs are also available on `uunet'. For example, to get the `info'
file, run:
uucp uunet\!~/vendor/sco/SLS/info /tmp/info
Most of these machines also have Enhanced Feature Supplements (EFSs),
games and graphics programs, and new termcap and terminfo terminal
definitions in addition to SLS. Look for an `info' or `README' file
one directory up from the `SLS' directory for more info.
QA6. I'm using an older Xenix/386 version. What fixes do I need?
Development System
- 2.3.0 or older An upgrade to 2.3.1 must be purchased from SCO.
- 2.3.1 Install `lng244'.
Operating System
- 2.2.X or older An upgrade to 2.3.4 must be purchased from SCO.
- 2.3.0 or 2.3.1 SCO would like you to purchase a 2.3.4 upgrade.
The `xnx137' fix would get you to 2.3.2, but SCO
does not provide it any longer.
- 2.3.2 Install `xnx296a' to get to version 2.3.3.
If you have VP/ix and installed update UFJ, then your kernel is
already at 2.3.3. None the less, you still want `xnx296a'. The
`xnx296a' update is also known as UFN, and replaces UFJ and UFM.
UFM was also known as the `xnx155b' update.
You must install the development system before `xnx296a'.
`xnx296a' provides you with most of the important fixes in 2.3.4.
You will lack some of the nice enhancements such as updated man
pages and the Korn shell.
SCO preconfigures the kernel for a very minimal system. You should
tune the kernel for your exact system configuration. See the
"Tuning Kernel Parameters" chapter in the System Administrator's
Guide.
QA7. Does SCO have a BBS?
Yes. The SOS Support BBS is $95/year. This is a good deal. You
can:
- download fixes, suggestions, and hints.
- keyword access to the support problems database.
- retrieve product info, release status, and hardware compatibility.
- get support via email.
- subscription to quarterly Discover newsletter.
You can dial-in with a terminal program such as `cu' -- uucp is
not required. Access is read-only, but most questions can be
answered by the support database. SCO currently doesn't provide
SOS access to most overseas users.
Previous versions of this FAQ suggested joining the `SCO Developer
Alliance'. For $100/year, it gave you BBS access along with other
benefits. Somebody within SCO must have finally come to their
senses and realized they were providing a worthwhile and valuable
service to their customers. Can't have that! So, effective Jan
94, they jacked up the price almost 500%, thus ensuring no product
offered by SCO could ever be remotely confused with a bargain.
If you are a member of a Fortune 500 company, you might want to
contact for info. If you are a small-time
developer, then kiss off, loser.
------------------------------
Subject: ***** SECTION B - General Xenix Questions
QB1. Can't boot. My system used to work.
Check the A: drive. If there is a floppy in there your system
might spew garbage on the monitor or hang during boot. If this
problem occurs right after rebuilding a new kernel, go read the
FAQ on disks bigger than 1024 cylinder.
QB2. Configure(ADM) fails when I modify my system name.
If you select a site name of two, three, or four characters,
`configure' will fail with an error message:
space.asm(XXX): error A2050: Value out of range
If the development system is installed, there is a workaround.
Do the following:
- cd /usr/sys/conf
- Edit `xenixconf'. Search for the `nodename' line and enter
the desired system name between the double quotes. For
example, for machine name = `foo' this line should read:
nodename "foo"
- Similarly, edit the `master' file and correct the `nodename'
line. For machine name = `foo' it should read:
nodename NODE "foo"
- Run `make'. This will rebuild the kernel data files and
then link a new kernel.
- Run `./hdinstall' to install the new kernel.
Reboot the system, and the new node name should be in effect. To
verify this, run `uname -a' after rebooting.
This bug has been fixed in 2.3.4.
QB3. The system is crashing with `parity error' panics.
Everybody knows there are eight bits to a byte. Why, then, do
PCs use 9-bit wide memory? That last bit is a parity check bit.
It lets the system detect when data get corrupted while sitting
in memory or in transit to the CPU.
Prior to Xenix 2.3.3, parity errors were silently ignored. In
these releases the system would continue to run -- for a while
anyway. These days, if a parity error is detected the system
will panic immediately and say:
PANIC: memory failure - parity error
Like the message says, this is almost always caused by memory
problems. If it happens, run a good memory diagnostic overnight
to try to locate the problem. Keep the cover on the computer
while running diagnostics; heat tends to push a marginal memory
chip into failure. Similarly, running the system with the cover
off might make the problem go away. If it does, possible causes
are marginal chips or bad ventilation.
This problem can also be caused by a marginal power supply. Xenix
boxes often have more power hungry peripherals than your run of
the mill MS-DOS PC. For example, suspect the power supply if the
panics occur as soon as the tape drive starts spinning.
QB4. Login fails without prompting for password.
If /dev/tty is missing or incorrect, you will get a `Login incorrect'
message without ever being prompted for a password. For security
reasons, the `login' program goes directly to /dev/tty to ensure
the password comes from the keyboard. Your `tty' device should
look something like:
crw-rw-rw- 2 bin bin 3, 0 Oct 24 04:09 /dev/tty
If necessary, use the `mknod' command to recreate it.
QB5. Can I use `gcc' instead of buying the SCO Development System?
Yes, but the task is bigger than you think. A compiler alone
doesn't do any good if you lack header files, libraries, linker,
etc. Don't forget about make, yacc, lex, etc. Fortunately, the
repertoire of GNU software has grown to the point where you can
fill in all these pieces. Many folks, particularly Steve Bleazard,
Ronald Khoo, and Kai Ruottu, have done a lot of work getting `gcc'
and the GNU utilities running on Xenix. So, with anonymous FTP
access and a little elbow grease, you can do it.
Steve and Ronald provided the first widely available kit to use
gcc under Xenix. Their package was based on the gcc-1.40 release.
The most recent version (we know of) available for SCO Xenix is
gcc-2.5.7, ported by Kai. The Xenix-specific patches are available
on `ftp.funet.fi:/pub/unix/386ix/xenix/gcc/gcc257.xenix', as well
as unix.secs.oakland.edu.
An alpha test version of a `libc' for Xenix is available from
kate.ibmpcug.co.uk (in /ftp/pub/xenix/libc) and unix.secs.oakland.edu
(in /pub/xenix); files XLIBC.README.Z and xlibc.shar.Z. It is
based on the Berkeley Networking Release 2 tape. This package
was developed for use with the gcc-1.40 kit, but might be of use
with more recent versions too.
QB6. Program `foobar' dumps core with a stack overflow. [Xenix 286]
Xenix/286 programs request a fixed amount of space for the stack
in the executable file header. A program that exceeds this limit
will crash with a core dump. To fix, change the header to ask
for more stack space. You can recompile your programs with the
`-F' flag to increase the stack size. You can change the stack
size of existing programs by running `fixhdr' with the `-F' flag.
This is not a problem on 80386 binaries that use a variable stack.
QB7. Spell cannot initialize hash table.
The `spell' script (included in the optional Text Processing
package) uses an 8086 binary. It needs to stuff a bunch of data
into a single 64K segment. If you exceed this limit, you will
get an error saying something like:
table = malloc(0xc848) fails
sbrk(0) = 0x3868
spell: cannot initialize hash table
You can usually get enough space for `spell' to run by clearing
out your environment first. To do this, add the following line
near the top of the `/usr/bin/spell' script:
unset `env | sed -e '/^PATH=/d' -e '/^PS1=/d' -e 's/=.*//'`
QB8. Will my laser printer work with the Text Processing Package?
Xenix `troff' is based on a version written long before the advent
of laser printers. The only thing old troff understands is C/A/T
typesetters. Chris Lewis's `psroff' allows old troff to work with
various devices, including Postscript and LaserJet printers.
Version 3.0 is available from the comp.sources.unix archives.
Another alternative is Rick Richardson's `jetroff', available in
the comp.sources.misc archives.
For production work, consider purchasing a device independent
troff. Some of the suppliers of `ditroff' are Elan, Image Network,
Leverage, and SoftQuad.
Another alternative is the `groff' package by the Free Software
Foundation. You can find it in any of the FSF archives -- but
you will need `g++' to compile it. You will still need a backend
program to use a LaserJet with `groff'. Some possibilities are
`psroff', `jetroff', and `dvi2xx' on ftp.wu-wien.ac.at.
QB9. Where is crypt?
Encryption programs, such as `crypt', are are categorized by the
US Government as munitions. (Three cheers for the cold war!)
SCO removes the crypt(S) procedure and crypt(C) command from Xenix
so it may be exported. US domestic customers may contact SCO to
obtain SLS LNG190B. If you simply need a crypt(S) procedure to
compile programs that do password checking, you may get the SLS
LNG255B `International Crypt SLS' from any of the aforementioned
archive sites. This provides a crypt(S) procedure that supports
encryption but not decryption, and it does not include the crypt(C)
command. A number of non-domestic archive sites, for example the
European GNU mirror sites, carry `crypt' replacements that were
developed outside the US to avoid this export silliness.
QB10. How can email handle `internet' addresses or use a `smart host'?
Neither the SCO Xenix mail transport (/usr/lib/mail/execmail) nor
the mail program (/usr/bin/mail) can handle so-called `internet'
addresses (e.g. joe@acme.com). Nor can they use a `smart host'
system to route your email to its final destination. If you want
to add these features, you need to install a replacement transport
and reconfigure the mailer to use this transport. For simple uucp
connectivity, we recommend smail2.5 (archive name `smail3' published
in comp.sources.unix volume 11). If you also need network
connectivity (e.g. SMTP mail) then you'll need a more full-featured
mailer such as smail3.1, sendmail, or MMDF.
Although smail2.5 fits right into the SCO mail system, some
modifications and installation tricks are required. Both Chip
Salzenberg (see the comp.sources.misc archives) and Chip Rosenthal
(contact chip@chinacat.unicom.com) have provided solutions.
Whatever approach you use, you must tell /usr/bin/mail to pass
messages off to execmail for delivery rather than handling them
itself. Do this by adding a line which says `set execmail' to
the /usr/lib/mail/mailrc file. You might also think about adding
a nice, full-screen mailer program such as Elm or Mush.
QB11. Where can I find freely available software for Xenix?
Many of the freely available programs on archive sites and published
on Usenet will run under Xenix with little or no modification. Assuming
you have the Xenix Development System to compile it! See news.answers
and comp.archives for information on archive sites.
The following systems maintain software archives that specialize in Xenix.
anomaly
Administrator: Michael P. Deignan
Description: Source code for SCO Xenix, Unix, and ODT
FTP Access: anomaly.sbs.risc.net [155.212.2.2], login=anonymous
information in /SOFTLIST
UUCP Access: 1-401-455-0347 (PEP), 331-3706 (V.32bis)
login=xxcp, passwd=xenix, information in ~/SOFTLIST
Mail Server: send email to "snarf@anomaly.sbs.com" with a Subject
of "snarf" and the lines "snarf address "
(replace with your email address) and "snarf
help" to receive more information
Comments: ftp is via serial connection so be patient, number of
connections limited to prevent congestion
Mirror Sites: novell-server.pstc.brown.edu:/home/ftp/sco
oakland.edu
Administrator: Ron Srodawa
Description: SCO Xenix ports, particularly GNU software
FTP Access: unix.secs.oakland.edu [141.210.180.2],
login=anonymous, files in /pub/xenix
wimsey
Administrator: Stuart Lynne
Description: SLSs, SCO Unix (not Xenix) software in `custom' format
FTP Access: ftp.wimsey.bc.ca [192.48.234.1], login=anonymous,
information in /READ.ME.FIRST, /ls-lR.Z
UUCP Access: 1-604-939-4782 (PEP), 1-604-937-7411 (V.32bis),
1-604-939-4756 (2400bps), login=nuucp, passwd=nuucp,
information in ~ftp/READ.ME.FIRST, ~ftp/ls-lR.Z
Guest Access: same phone numbers, login=guest, passwd=guest
Comments: ftp is via serial connection so be patient, mostly
Unix oriented but some of it might work with Xenix
unicom.com
Administrator: Chip Rosenthal
Description: A small archive of various Xenix tools.
FTP Access: ftp.unicom.com, files in /pub/sco-xenix
Comments: This archive contains some of the code I've posted
to comp.unix.xenix.sco over the years.
QB12. Why don't my arrow keys work in `vi'?
For versions 2.3.3 and prior, probably because your `termcap'
entry does not have then defined properly. For version 2.3.4,
it's because `vi' is broke. If you have an older version of Xenix
laying around, you might consider grabbing `vi' off of it instead.
Note, however, that 2.3.4 `vi' gets its terminal information from
the `terminfo' database, while prior versions use `termcap'.
QB13. Why does `cron' die periodically?
Because of a bug that gets triggered by looooong periods of
inactivity. The problem is that if you don't give `cron' something
to do, an internal counter overflows and it dies. The solution?
Give it something to do! Use `crontab' to add something like this:
0 * * * * /bin/true
That runs the `true' command once an hour, on the hour.
------------------------------
Subject: ***** SECTION C - Disk and Filesystem Questions
QC1. Can I use a disk bigger than 1024 cylinders?
Yes. However, your root filesystem cannot extend beyond the 1024th
cylinder, because that's as far as the BIOS can reach when booting
the system. The BIOS is bypassed after Xenix boots, so cylinders
beyond 1024 can be accessed once Xenix is running. It is not
necessary to use a sector translation mode controller to reduce
the number of cylinders. The translation mode is very slow.
QC2. Why won't Xenix recognize my SCSI disk?
Not all versions of Xenix support SCSI. Those that do only support
certain SCSI adapters. First, verify your N1 floppy says `Type:
386GT' and not `Type: 386AT'. The AT version of Xenix (now
obsolete) does not include any SCSI support.
The GT version supports a limited number of SCSI host adapters.
The Adaptec AHA-154x is supported. We've also used compatibles
such as the Buslogic BT-542B. 2.3.4 added support for the
WD-7000-FASST2. If you've got something different, you have to
get a driver from the board vendor. The `SCO Hardware Compatibility
Guide' (contact SCO sales for one) should be consulted whenever
you have any hardware compatibility questions.
Some typical installation mistakes are:
- SCSI ID jumper for the root (boot) hard disk must be ID=0.
- The BIOS must be set for drive C:=NONE in the CMOS setup program.
- I/O port, memory address, or interrupt misconfiguration/conflict.
- Terminating resistors installed only at ends of ribbon cable.
- The parity jumper should be enabled on all drives and controllers.
A word on terminating resistors: Terminators must be installed on
the two devices at the end of the SCSI chain. If you have no external
devices then one end of the chain will be the SCSI adapter -- so it
gets terminators. The last device on the ribbon cable also needs
terminators. The terminators must be removed from everything else on
the SCSI chain.
Note that some SCSI disk controllers mimic the standard ST-506
interface. No special support is required for them; Xenix boots
thinking you've got a plain old disk controller. See the instructions
that came with your controller for details on cabling, strapping,
terminating, etc.
Note: If you are using Xenix 386GT 2.3.1-2.3.3 you should install
xnx252b for ISA or xnx150 for MCA. This is an improved SCSI driver
that yields a significant performance improvement.
QC3. Where is the `/u' filesystem I created?
When you create filesystems during the install procedure or with
`mkdev hd', the filesystem is initialized but it isn't configured
into the system. To perform that final step you need to run `mkdev
fs'. For example, if you created a `/u' filesystem, run:
mkdev fs /dev/u /u
QC4. `WARNING!! - mounting: as ' message when booting.
Due to a bug in the `mkdev fs' program, filesystems mounted below
the root directory are labeled wrong. For example, if you mount
a device `/dev/news' onto directory `/usr/spool/news', then you
will get a warning message when going into multi-user mode. That's
because `mkdev fs' labels the filesystem with the first component
in the pathname (`usr' in this example) when it really should be
the last component in the pathname (`news' in this example).
This message is merely an annoyance and will not hamper system
operation. To eliminate the warning, relabel the filesystem with
the last component of the mount directory. For the above example,
you may change the label from `usr' to `news' by running the command:
fsname -s news /dev/news
QC5. `POSSIBLE FILE SIZE ERROR' when running `fsck'.
If `fsck' says `POSSIBLE FILE SIZE ERROR I=nnnn' don't panic. It
almost always means `fsck' found a `sparse file', not a true
filesystem error. A sparse file has holes in it. They are created
when a program skips over sections of a file it is writing. The
Xenix filesystem doesn't even bother allocating disk blocks for
those holes, it just says the gaps are full of zeros. The complaint
occurs because `fsck' calculates the number of disk blocks needed
to store the file, counts up the number of disk blocks actually
used by the file, and complains that the two don't match.
When you get a file size error from `fsck' you should note both
the `I=nnnn' inode number logged in the message and the filesystem
which was being checked. You can see what the file is by running
the following command:
ncheck -i
where is the number logged in the error message and
is the pathname of the filesystem device, e.g. `/dev/u'. Chances
are the file will either be a dbm(S) database file (in which case
ignore the complaint, it's expected) or a `core' dump (in which
case delete the `core' file).
QC6. Is disk fragmentation curable?
Not easily. However, the steps to slow down fragmentation are
pretty simple.
Xenix maintains a list of available disk blocks. As files are
deleted, the released blocks are appended to this free list.
Ideally, adjacent disk blocks would be used to create and grow
files so that all the parts of the file sit together on the disk.
Disk blocks, unfortunately, are allocated to files in the order
they appear on the free list and without regard for location.
Eventually, new files will be created with their data blocks
scattered all around the disk. This fragmentation is undesirable
because it slows down disk accesses.
To slow down the tendency towards fragmentation, periodically
reorder the blocks in the free list. To do this, dismount the
filesystem (with `/etc/umount') and run `fsck -S'. You will get
a message saying:
FILE SYSTEM NOT MODIFIED, STILL DIRTY.
Don't worry -- ignore that message.
To determine how badly your filesystems are fragmented, run
`fsanalyze' by Michael J. Young, from comp.sources.misc. You will
need patchlevel 3 to analyze Xenix filesystems.
The conventional cure for filesystem fragmentation is:
- Make a full backup of the filesystem. Use `cpio' (or `afio' if
you've got it). Do NOT use `tar'. It doesn't backup device
nodes, pipes, or directories. You could use `dump', but we find
it awkward. (n.b. Earlier versions of this FAQ claimed that
`dump' would restore in a fragmented manner. That is incorrect.
Sorry for the misinformation.)
- Recreate an empty filesystem with `divvy' or `mkfs'. `divvy'
is easier to use -- simply select the `create' option. However,
`mkfs' will be required if you want a non-default number of
inodes. Invoke `divvy' with:
/etc/divvy -c 1 -b 1 # for 1st physical disk
/etc/divvy -c 1 -b 1 -p 1 # for 2nd physical disk
- Reload the filesystem from the backup.
- Regenerate the `lost+found' directory. Run:
# Substitute appropriate name for `foo'.
/etc/fsck /dev/foo
/etc/mount /dev/foo /foo
mkdir /foo/lost+found
for i in 1 2 3 4 5 6 7 8 ; do
for j in 1 2 3 4 5 6 7 8 ; do
touch /foo/lost+found/x$i$j
done
done
rm /foo/lost+found/x??
/etc/umount /dev/foo
Be very careful with this procedure. We suggest you verify your
backup is readable before zapping the filesystem. One mistake
(especially when running `mkfs' or `divvy') will trash everything.
The filesystem you trash may be your own.
QC7. Can I put a CD-ROM drive on my Xenix system?
No. Sure, it would be easy for somebody to write a device driver
to talk to a CD-ROM drive. But that's not the whole story. If
you want to use a CD-ROM, you need to be able to mount it as an
ISO-9660/High Sierra filesystem. That's not so easy. See the
FAQ on NFS for additional info.
------------------------------
Subject: ***** SECTION D - Communications Questions
QD1. How do I add more than 2 COM ports?
Dumb serial cards (and internal modems) may be configured for Xenix
as COM3 and COM4 -- with one big caveat. Each COM port requires its
own interrupt number. If you have an unused IRQ and the Development
System, you may build additional COM ports into the kernel. To
illustrate the procedure, we will add a COM3 configured as follows:
I/O Addr: 0x3E8
IRQ: 5
device: /dev/tty3a Major=5, Minor=4
/dev/tty3A Major=5, Minor=132
Serial devices are a two-fer, you get a "direct" device (tty3a)
and a "modem control" device (tty3A). The two are distinguished
by the minor device numbers -- add 128 to get the "modem control"
device number.
The device minor number you select *must* be in the range of 0
through 15 inclusive. That's because the driver does bit twiddling
that assumes the device unit number is located in the four least
significant bits of the minor number. (Older versions of this
message not only failed to point this out, but gave an example
that would not work due to a bogus minor device number selection.)
1. Edit `/usr/sys/io/sioconf.c'.
The two lines in this file that describe COM1 and COM2 are:
{0,IBM_BOARD, 1,4,0, (sd)0x3f8,0, 0,MCRBIT3}, /*ibm COM1*/
{1,IBM_BOARD, 1,3,8, (sd)0x2f8,0, 0,MCRBIT3}, /*ibm COM2*/
Add a line that says:
{2,IBM_BOARD, 1,5,4, (sd)0x3e8,0, 0,MCRBIT3}, /*ibm COM3*/
See `/usr/sys/io/sioconf.h' for details.
2. Edit `/usr/sys/conf/master'.
The serial ports are defined by the line:
sio 4 0577 104 sio 0 0 5 1 7 3 4 33 34
The last four fields define the interrupt numbers used. Change
the `33' to a `5' since COM3 will be on IRQ5. For reference,
here is the mapping between IRQ lines and the master file
`magic numbers':
IRQ0 0 IRQ4 4 IRQ8 30 IRQ12 34
IRQ1 1 IRQ5 5 IRQ9 31 IRQ13 35
IRQ2 31 IRQ6 6 IRQ10 32 IRQ14 36
IRQ3 3 IRQ7 7 IRQ11 33 IRQ15 37
3. Rebuild the kernel. Run:
cd /usr/sys/conf
make
Do not use `link_xenix' here. You need to run `make' to get
`sioconf.o' and the kernel data files rebuilt.
4. Install the new kernel. Run:
/usr/sys/conf/hdinstall
This will make a backup of your current kernel to `/xenix.old'.
5. Create the device nodes. Run:
mknod /dev/tty3a c 5 4
mknod /dev/tty3A c 5 132
Reboot your system, and the new serial port should be there.
QD2. How do I set a 19,200 baud rate?
For historical reasons, terminal speeds of 19200 and 38400 are
called `EXTA' and `EXTB'. So, in the `/etc/gettydefs' file you
need to say `EXTA' and `EXTB', not 19200 and 38400. These speeds
are already available there as entries `n' and `o', respectively.
Similarly, with the `stty' command you need to say:
stty 9600 # set to 9600
stty exta # set to 19200
stty extb # set to 39400
A smart serial card is recommended for these two highest speeds.
QD3. How can I have more mscreen(C) sessions?
The mscreen(C) facility provides multiple sessions from a serial terminal
by `multiplexing' your terminal (tty) line onto several pseudo-terminal
(pty) lines. Xenix is shipped with eight ptys enabled, that provides
a system-wide limit of eight sessions through the mscreen(C) command.
First off, you need to determine whether you are allocating mscreen(C)
sessions wisely. For example, SCO ships an `/etc/mscreencap' file
that runs six sessions on a WY-60 terminal. If you edit `mscreencap'
and cut this down to three you immediately double the number of people
who can run mscreen(C).
You cannot increase this number beyond eight if you are running TCP/IP.
(More about this in a moment.) If you are not running TCP/IP, then
you can increase the number of possible mscreen(C) sessions by: first
creating more ptys in the kernel, second creating the device nodes
for the new ptys, and finally placing a `getty' upon each of these
new ptys.
To create more ptys in the kernel, increase the `nspttys' kernel
parameter. With Xenix 2.3.4, run the `configure' command interactively
and select the `Multiscreens' option. For older versions of Xenix,
run `configure' manually. For example, to provide sixteen ptys, run:
cd /usr/sys/conf
./configure nspttys=16
Once `nspttys' is set, run `link_xenix' and `hdinstall' to build and
install a new kernel.
Next, you need to create the device nodes in the /dev directory for
these additional ptys. Unfortunately, mscreen(C) uses a very poor
naming strategy for ptys beyond the 8th. Once you go beyond the
/dev/ttyp7 in the base Xenix distribution, mscreen(C) next looks for
not /dev/ttyp8, but rather /dev/ttyp01. Therefore you should create
the eighth pty with the commands:
cd /dev
mknod ttyp01 c 54 8
mknod ptyp01 c 55 8
chmod 666 ptyp01
chmod 644 ttyp01
You might notice that these names are the same ones used by `rlogind'
and `telnetd' under SCO TCP/IP. Unfortunately, to use these ptys for
mscreen(C) you need to place a `getty' on them -- but if you do then
rlogin/telnet will break. Those running TCP/IP (and not weak of heart)
can try editing the `/dev/ttyp' string in the `mscreen' binary and
totally rename the pty devices.
An alternative method to relieve the conflict between `mscreen'
and TCP/IP is to use an `.mscreenrc' file. If you create a surplus
of TCP/IP ptys, you can steal some of them for `mscreen'. Just
create an `.mscreenrc' and enter the names of the ptys you want
`mscreen' to use. Since the TCP/IP utilities start at the bottom,
steal from the top and work down. The catch? You have to put an
`.mscreenrc' file into the home directory of *every* user who will
be using `mscreen'. Bleych.
If necessary, ensure you edit `/etc/ttys' to add the new ptys.
Don't forget to `enable' the lines to start a `getty' on them.
QD4. Upgraded to 2.3.4 and flow control broke with mscreen(C).
The 2.3.4 version of mscreen(C) was changed to run the tty line
totally raw. This is required so that the ^S and ^Q keys are
passed on to programs that need them, such as `emacs' and Foxbase.
An unfortunate side effect of handling flow control on the other
side of the session rather than directly by the tty is that response
to flow control is a lot more sluggish. Now, when you hit ^S you
might get another screenful of data before the display actually
freezes.
If you never run any applications that require full 8-bit transparency,
one way to make flow control more responsive is to rename `mscreen'
to `/usr/bin/mscreen.sco' and install the following script in its
place:
:
tty=`tty`
( sleep 5 ; stty ixon <$tty ) &
exec mscreen.sco
QD5. Terminals act funny, modems drop characters, help!!
If you are losing characters on your serial lines, consider the
following steps:
* Ensure that flow control is working right.
* If you are running dumb COM ports, either upgrade the UART chips
to 16550As or switch to a smart serial card.
* If you have a lot of users or lots of high speed data lines,
increase the number of `clist' buffers in the kernel.
* If you upgraded to 16550A UARTs and this helped but did not
solve the problem, then adjust the FIFO trigger level.
* If you are running high speed lines on a loaded system, adjust
the `ttyhog' value.
When diagnosing serial problems, start at the top of this list
and work down. If your flow control is broke, it will do no good
to go poking around inside your Xenix kernel.
QD6. Does Xenix support 16550A UARTs?
The guts of a standard COM port is a UART (universal asynchronous
receiver/transmitter) chip. Most serial ports use the 16450 or
an equivalent chip. The 16550A is a pin-compatible, drop in
replacement which adds 16-characters of on-chip FIFO buffering.
The FIFOs reduce system loading and increase performance.
Starting with 2.3.4, the `sio' driver recognizes 16550A UARTs and
enables the on-chip FIFOs. Older versions of Xenix merely treat
this chip as an expensive 16450. You can get 16550A support with
any version of Xenix by installing the FAS driver written by Uwe
Doering and based upon Jim Murray's `asy' driver. FAS was published
in alt.sources, and is available at most reputable archive sites.
We recommend sticking with the National Semiconductor NS16550A.
Many manufactures make usable 16450 clones, but some of the 16550
compatible chips aren't so compatible. Also, older versions of
the 16550 are known to be broken. Ensure yours have an `A' suffix.
QD7. How do I increase the number of `clists'?
Xenix buffers terminal characters in data structures called
`clists'. There is a fixed pool of clists on the system, and when
that supply is exhausted incoming characters are dropped. Therefore,
the more active users you have on your system, the larger this
pool of clists should be. The default configuration is 100 clists.
Each terminal line requires an average of 5 to 10 clists. High
speed modems need more. A conservative strategy would be to
allocate 15 clists per active terminal. For example, if you have
16 serial ports and 4 console screens active at once, allocate
(16+4)*15 or 300 clists.
To see the number of clists on your system, login as root and run:
cd /usr/sys/conf
./configure -y NCLIST
To change the number of clists, say to 300, login as root and run:
cd /usr/sys/conf
./configure NCLIST=300
then rebuild and install a new kernel and reboot.
QD8. How do I change the 16550A trigger level?
If installing a 16550A UART helped but didn't totally fix a lost
character problem, and your system is heavily loaded, then there
is something else you can try. If you installed a 16550A and
there was no effect at all, then skip this -- it won't help.
The Xenix `sio' driver initializes the 16550A with a trigger level
of 14. This means that under continual data streams the UART will
wait until 14 characters accumulate before telling Xenix to come
get them. This gives the system two character times to get in
and service the COM port. If Xenix does not service the port in
that time the 16-character buffer will overflow and and characters
will be dropped. This might happen on a heavily loaded system.
The trigger level is initialized at boot time from the 16-byte
`sio_fifoctl[]' array. This array specifies the UART control
register initialization values for device minor numbers 0 through
15. Or more exactly, the minor number is ANDed with 0x0F to get
the index into this array. For example, the initialization for
/dev/tty2a (minor=8) is in `sio_fifoctl[8]'. The possible values
are as follows:
sio_fifoctl: 0xCF 0x8F 0x4F 0x0F
trigger level: 14 8 4 1
The standard value is 0xCF. A smaller value will notify the system
earlier that characters are waiting, thus providing the system
more time to service the port, but increasing the number of
interrupts generated by the port.
As an example, here is how to change the trigger level for /dev/tty2a
(and /dev/tty2A) to 8 characters (code=0x8F):
cp /xenix /xenix.save # make a backup!
adb -w /xenix # use "/etc/_fst" if no "adb"
* sio_fifoctl+8/x
sio_fifoctl+0x8: 0xcfcf
| |
| `---- This is the 8-bit value for the
| port we want (minor=8).
|
`------ This is the 8-bit value for the
next port (minor=9).
* sio_fifoctl+0x8/w 0xcf8f
sio_fifoctl+0x8: 0xcfcf= 0xcf8f
* $q
QD9. How do I adjust the `ttyhog' value?
Since Xenix has a fixed pool of clists, the kernel tries to prevent
one tty from hogging all of them. The limit is defined by `ttyhog',
and defaults to 256 (0x100 hex). This limit might be too low if
you've got some particularly fast devices on a particularly slow
system. To change the `ttyhog' value you must patch the kernel
image. The following increases `ttyhog' to 512 (0x200 hex).
cp /xenix /xenix.save # make a backup!
adb -w /xenix # use "/etc/_fst" if no "adb"
* ttyhog/x
_ttyhog: 0x100
* ttyhog/w 0x200
_ttyhog: 0x100= 0x200
* $q
QD10. BSD based uucp can't connect to my machine.
BSD based uucp sends even parity. Xenix uucp expects no parity.
Add:
"" P_ZERO
to the chat script in their (not your) `Systems' or `L.sys' file.
For example, the following works on a Sun 3:
xnxbox Any uucp 19200 5553333 "" P_ZERO "" \r in:--in: nuucp
QD11. uucp truncates my system name to seven characters!
This misfeature was introduced in the xnx155b supplement. The
story we hear is that SCO broke their `uucp' to cater to systems
that choke on long system names. There is a workaround. For
system name = `verylongname', add to every record in the
/usr/lib/uucp/Permissions file:
MYNAME=verylongname
Next, rename /usr/bin/uuname to /usr/bin/uuname.sco. Replace
/usr/bin/uuname with:
:
if [ $# -ne 1 -o "X$1" != "X-l" ] ; then
exec /usr/bin/uuname.sco $@
exit 1
fi
head -1 /etc/systemid
exit $?
This allows programs using `uuname' to receive the correct,
untruncated name.
QD12. What is the uucp `windows' patch?
uucp transmits data in packets, usually 64 bytes apiece. An
acknowledgment is required for every packet sent -- but not
immediately. A window of unacknowledged packets is allowed. The
default window size is three, that means `uucico' won't stop
sending unless it falls more than three packets behind. A three
packet window isn't big enough for very fast media and long delay
media. The `uucico' binary can be patched to increase the window
size by the following manual procedure:
cd /usr/lib/uucp
cp uucico uucico.old # make a backup copy!!
adb -w uucico
* windows/x # display windows value
_windows: 0x3
* windows/w 7 # change it to seven
_windows: 0x3= 0x7
* $q # done
If you have Xenix 2.3.4 but not the Development System, use
`/etc/_fst' instead of `adb'. If you can't find adb on your
system, look on the N02 disk.
This change increases the window size to seven -- the maximum
possible. A similar change must be performed on the remote system's
uucico because the actual window size is negotiated as part of
the protocol startup.
QD13. uucp gives `alarm' messages, eventually dies.
If you run uucp in debugging mode (`uutry -x9') and see it get
stuck like:
alarm 1
send 37777777621
alarm 2
send 37777777621
alarm 3
send 37777777621
alarm 4
send 37777777621
and eventually die, this means your system got jammed waiting for
a response that never came. The most common cause of this problem
running uucp across a modem with XON/XOFF flow control enabled
(e.g. a Telebit modem with S58=3). You can't do that; you must
run with no flow control or RTS/CTS handshaking (on a Telebit that
would be S58=0 or S58=2, respectively). Other possible causes of
this problem are serial cards with broken handshaking or running
out of clists.
------------------------------
Subject: ***** SECTION E - Display and Graphics Questions
QE1. How come Xenix won't recognize my VGA display?
Probably because you are running a very old version of Xenix.
VGA support was introduced in release 2.3.0.
QE2. How can I do a printscreen under Xenix?
MS-DOS users can produce a screen printout with one keystroke.
Xenix does not offer this builtin capability. SCO's MultiView
product provides this. Also, it can be simulated with the following
script:
:
# @(#) prtscrn Print Screen
# execute from cu as ~!prtscrn
oldstty=`stty -g` # save stty
stty -echo ixon ixoff -ixany # no echo
/bin/echo '\033[2i\c' # send screen to host
# grab 24 lines, clean up trailing blanks, print it
sed -e 's/ *$//' -e 24q | lp
stty $oldstty # put stty back when done.
Another approach is the `prtscrn2' program by Chip Rosenthal. It
grabs the contents of any console screen and sends it to standard
output. See comp.sources.misc.
QE3. How can I blank the console display when it is idle?
A screen blanker is built into the new console driver, provided
by 2.3.4 or 2.3.3 via SLS xnx296a. It is finicky about the hardware
it likes. Anything less than a VGA display will not work. To
enable the blanker, as root:
cd /usr/sys/conf
./configure
Select option 6 (MultiScreens) and enter a non-zero value for TBLINK.
(The manual incorrectly calls this TBLNK.) Then ./link_xenix and
./hdinstall.
If the built-in blanker doesn't like your video adapter or you
have an older version of Xenix, save the following script to a
file and run it out of cron every fifteen minutes or so. It will
check if all console multiscreens have been idle for ten minutes
or more, and if so switch the display to an unused screen (as
configured by SCRN).
:
who -u | awk '
$2 !~ /^tty[01][0-9]$/ {next} # Not a console screen.
$6 == "." {exit(1)} # Screen in use.
$6 ~ /^0:0/ {exit(1)} # Not idle long enough.
' >/dev/null 2>&1
if [ $? -eq 0 ] ; then
# Leading "\0" aborts any pending escape sequence.
SCRN=10
echo "\0\033[${SCRN}z\c" >/dev/tty01
fi
QE4. How can I do graphics under Xenix? What programs are available?
There are two approaches to graphics programming. At the very
lowest level, the screen(HW) manual page describes ioctl() codes
to access the video display memory and controller. Device-independent
graphics is provided by the Computer Graphics Interface (CGI)
package included with the Xenix Development System. CGI drivers
are provided for VGA, EGA, and Hercules displays; Epson, LaserJet,
and Postscript printers; and HP plotters. Several programs have
been posted to the net that run under CGI, such as gnuplot,
starchart, and gif. See comp.sources.misc.
QE5. CGI graphics mangles grey scale on a mono VGA.
SCO fixed their monochrome VGA driver in version 2.3.3. The
default color mapping in CGI maps many colors with the identical
total intensity. They appear as the same shade grey-scale display.
Try using the CGI functions vs_color() and/or vsc_table() to create
a color map that works with your display. Try vsf_style() to
create hatching or other fill-patterns in place of colors.
QE6. CGI graphics fail on a LaserJet in landscape mode.
A bug in the CGI 1.1.0 LaserJet driver causes all output to
appear on a single line. In landscape mode the driver puts out
a spurious escape sequence `\033&a864V' that forces all output
to the same position on the page. You can either remove the
offending escape sequence from the driver with a binary editor
(keep a backup copy), or use a filter to clobber that sequence
from the output.
------------------------------
Subject: ***** SECTION F - Networking Questions
QF1. What do I need to run TCP/IP?
The SCO TCP/IP Run-Time includes *almost* everything you need to
connect a Xenix system to a TCP/IP network. You get the drivers
for several popular network interface cards (NICs), the protocol
stacks, and most of the familiar programs like `telnet' and `rcp'.
We say `almost' because the TCP/IP package requires Streams, and
that's an extra-cost option. You need to buy and install the
Streams Run-Time before you can load TCP/IP. Furthermore, if you
want to develop or compile network programs, you will need the
TCP/IP Development System too.
QF2. What do I need to run NFS?
Unix. :-)
Nobody offers an NFS for Xenix, and don't hold your breath waiting
for one. It is very difficult adding new filesystem types to
Xenix. The `FS' in NFS does stand for `File System' after all.
Newer versions of Unix provide mechanisms that allow new filesystem
types to be added easily (the `vnode' mechanism in BSD Unix and
the `filesystem switch' in System V 3.2 and beyond). With Xenix,
the filesystem support must be coded right into the kernel. The
task of merging NFS code with VP/ix hacks, Xenix-net hacks, etc.
is more than can be justified. And because it requires kernel
source, it is unlikely a third party would do this.
QF3. How can I run uucp over TCP/IP?
The Xenix `uucico' doesn't know about networking, and the Xenix
TCP/IP package doesn't do anything to solve that problem. Chip
Rosenthal has published a program called
`uucpm' that works around this problem to allow an SCO Xenix system
perform uucp transfers across the network. Contact him if you
need a copy.
QF4. What does "NOTICE: tcp sum: src C06C6901, sum 0000B004" mean?
That a bad TCP segment was received. One possible reason for this
is a buffer overrun caused by a slow system, a lousy network card,
or a heavy network load. Most TCP/IP implementations silently
detect these errors and ask the remote system to re-transmit.
SCO's TCP/IP decides to whine to the console as well.
You can tell what the other system is by getting out your hex
calculator (c.f. the bc(C) command) and plugging in the `src'
address. In the above example, 0xC0=192, 0x6C=108, 0x69=105, and
0x01=1. So the sending machine was 192.108.105.1.
If you get these messages on occasion or only under heavy network
load, don't worry too much. If they are frequent then consider a
faster network card with more buffering, a faster computer, or
go looking for cabling problems.
If you get tired of seeing these messages, you can shut them off:
cp /xenix /xenix.save # make a backup!
adb -w /xenix # use "/etc/_fst" if no "adb"
* tcpprintfs/d
_tcpprintfs: 1 # currently "1" -> enabled
* tcpprintfs/w 0 # set to "0" -> disabled
_tcpprintfs: 0x1= 0x0
* $q
------------------------------
Subject: ***** SECTION X - Xenix and MS-DOS Interoperability Questions
QX1. Can Xenix share a hard disk with MS-DOS?
Yes. SCO directly supports an MS-DOS 3.2 partition on the same disk as
your Xenix partition. You must:
- Install MS-DOS 3.2 bootable partition as the FIRST partition.
- Install Xenix bootable as the next partition.
- Select Xenix as the `active' partition.
At the
Boot
:
prompt either type `dos' for MS-DOS boot or press ENTER for Xenix.
If you create any other type of partition (e.g. one of the new,
larger sized MS-DOS 5.0 partitions) or forget to create the MS-DOS
partition before loading Xenix, then you can still access it by
booting from a floppy disk.
It is possible to provide `dual boot' capability for other partition
types, for example MS-DOS 5.0 large partitions, by making a modified
version of the /dos program. The following instructions, based
upon a procedure by Vic Michael , show how.
su # become superuser
cp /dos /dos5 # make a new version of dos5 program
adb -w /dos5 # use "/etc/_fst" if no "adb"
* 0x3f:0x61?i # examine instruction at 0x61
0x3f:0x61: add al,0x4
* 0x61?w 0x604 # change '0x4' to '0x6'
0x3f:0x61: 0x404= 0x604
* 0x61?i # verify change
0x3f:0x61: add al,0x6
* $q
Now, you can say `dos5' at the `Boot' prompt to start MS-DOS. You
will NOT, however, be able to use the `dos(C)' tools to access this
partition from Xenix.
QX2. Can Xenix access MS-DOS disks?
Yes, with limitations. The commands on the `dos(C)' manual page
provide access to MS-DOS disks (floppy and fixed) under Xenix.
The limitation is that only conventional MS-DOS 3.2 hard disk
partitions can be recognized. Extended MS-DOS 3.2, old MS-DOS
1.0, and large MS-DOS 4.0/5.0 partitions cannot be accessed with
the existing tools.
If you run into problems with the dos(C) commands, check that
`/etc/default/msdos' provides proper aliases for the A:, B:, etc.
devices. Also, if root can access the MS-DOS fixed disk but users
can't, check the permissions on /dev/hd0d (the Xenix name of the
MS-DOS partition on the first fixed disk).
The `mtools' package by Emmet Gray in comp.sources.misc provides
better handling of MS-DOS devices under Xenix. Modify the
`devices.c' file to understand Xenix device naming.
#ifdef M_XENIX
struct device devices[] = {
{'A', "/dev/install", 0L, 12, 0, (int (*) ()) 0, 0, 0, 0},
{'B', "/dev/install1", 0L, 12, 0, (int (*) ()) 0, 0, 0, 0},
{'C', "/dev/hd0d", 0L, 16, 0, (int (*) ()) 0, 0, 0, 0},
{'D', "/dev/hd1d", 0L, 16, 0, (int (*) ()) 0, 0, 0, 0},
{'\0', (char *) NULL, 0L, 0, 0, (int (*) ()) 0, 0, 0, 0}
};
#endif /* M_XENIX */
If you assign `/dev/install' to the `A' drive, you don't need to
worry about disk density when reading and writing. However, you
need to specify the full device name when formatting. For example,
to format a high-density disk in drive A: you must specify the
full device name:
dosformat /dev/fd096ds15
QX3. Can Xenix execute MS-DOS programs?
Yes. You must purchase SCO VP/ix. VP/ix emulates an 8086 PC/XT
running MS-DOS. The compatibility provided by VP/ix is fair with
a significant performance penalty. VP/ix will not run programs
that use 80286 or 80386 instruction codes. VP/ix is not available
for Xenix/286.
QX4. Can MS-DOS execute Xenix programs?
No. With the Xenix Development System, you can compile programs
to execute under MS-DOS with the `-dos' command line switch.
------------------------------
Subject: ***** SECTION Z - The (in)Famous Xenix Cheat-Sheet
QZ1. What the $%*&! is happening?
Who am I? /usr/bin/who am i
Where am I? /bin/pwd
What am I doing? /bin/ps -f
Am I having fun yet? /usr/games/worms -R
What's my user/group id? /usr/bin/id
Who did I login as? /usr/bin/logname
What's my terminal? /bin/tty
What are my terminal parameters? /bin/stty -a
Is terminal flow control working? /usr/games/stars
What is my current crontab file? /usr/bin/crontab -l
Do I have uucp jobs queued? /usr/bin/uustat
What is the system doing? /usr/bin/w
How is the system running? /usr/bin/vmstat 10
Has the system been swapping? /usr/bin/vmstat -s
Open files, inodes, processes? /bin/pstat | grep '^[0-9]'
What are the kernel parameters? /usr/sys/conf/configure -x
What versions are installed? egrep "#prd|#set|#rel" /etc/perms/*
What are the hardware settings? /etc/hwconfig -h
Is /etc/passwd correct? /etc/pwcheck
Is /etc/group correct? /etc/grpcheck
Is /etc/gettydefs correct? /etc/getty -c /etc/gettydefs
Do all files have owners? /usr/bin/quot
Who is using all the disk space? /usr/bin/quot
When did joe last login? /usr/bin/last joe
What files are owned by UID=944? find / -user 944 -exec l -d {} \;
Are file perms/owners set OK? cd / ;
/etc/fixperm -n /etc/perms/rts
How about perms on uucp files? cd / ;
/etc/fixperm -nd UUCP /etc/perms/rts
Check uucp file consistency. /usr/lib/uucp/uucheck
What are uucp access permissions? /usr/lib/uucp/uucheck -v
What is the print spooler doing? /usr/bin/lpstat -t
Stop the scheduler. /usr/lib/lpshut
Restart a printer. /usr/lib/accept printer_name ;
/usr/bin/enable printer_name
[Following apply only if TCP/IP is installed.]
Where am I? /usr/bin/hostname
Is system foo alive? /usr/bin/ping foo
What machines are connected? /usr/bin/netstat
How is the network doing? /usr/bin/netstat 10
Where are the packets going? /usr/bin/netstat -r
Network not work? /usr/bin/netstat -s
[Thanks to Jeff Liebermann.]
------------------------------
Subject: ***** The Fine Print
This collection is Copyright 1992-1994, Unicom Systems Development, Inc.
All rights reserved. Permission granted to reproduce and distribute this
document provided this notice remains intact and any changes to the document
are clearly marked. We have tried to review all information, but cannot
guarantee it for any particular purpose. We do not offer any warranties or
representations, nor do we accept any liability for any damage resulting
from the use or misuse of information or procedures in this document.
End of sco-xenix FAQ
********************
|
Home
